Do Adhesive Tackle Mounts Really Hold on a Boat?

Last Updated: October 30, 2026

Quick Summary

Adhesive tackle mounts will hold well on a bass boat when they are installed correctly. The bond depends on clean, dry surfaces, a suitable placement, and allowing the full cure time before loading baits. Mounts that are rushed or installed on dusty or waxed surfaces are the ones most likely to fail.

  • Clean the surface with isopropyl alcohol, wiping twice, and let it dry completely before mounting.
  • Choose a flat, smooth area where the mount pad sits flush.
  • Wait the full cure time (24 hours) in the adhesive instructions before mounting the clip strips or loading any baits.

Table of Contents

Anglers often ask whether adhesive tackle mounts really hold on a bass boat, especially once the water gets rough. Easy View Tackle Systems designed its patent clip strips and foam-filled crankbait hangers to mount inside storage compartments and under lids with adhesive or screw hardware, so every bait stays dry, visible and ready to retrieve. The short answer depends on how the mount is installed, since surface prep and placement decide whether it stays put.

I M G 0500
I M G 0500

I M G 0

Surface Preparation and Curing for a Secure Bond

Step 1, Pick the right spot. Choose a flat, smooth section inside the compartment or under the lid where the clip strip or hanger will sit flush. Avoid curved corners. The mount needs full contact across its whole footprint; A pad that only touches on the high spots is already compromised.

Step 2, Clean, then clean again. Wipe the surface with isopropyl alcohol and a clean lint-free cloth to strip dust, wax, residue, and the mold-release film that may be on new fiberglass and plastic. Wiping twice helps remove residue that a single pass can leave behind. Also clean the back side of the mounting pad with isopropyl alcohol let the surface dry completely. Adhesive will not bond to moisture.

Step 3, Match the pad to the surface.

  • Fiberglass and gelcoat: Waxed or freshly polished area; Clean the area well with acetone or paint thinner to remove the polish or wax then use isopropyl alcohol with a clean cloth to remove any residue on the surface area to be bonded. Wipe bonding area and the back of the mounting pad dry with clean dry fiber cloth. Let dry for 15 minutes before applying the adhesive.
  • Painted surfaces: Bond depends on how well the paint is adhered. If paint is flaking or chalky, the pad will take the paint with it when it fails.
  • Smooth plastic: Bonds well on non-porous plastic, but textured or porous plastic reduces contact area and needs more pressure and a longer cure.
  • Metal: Bonds well when proper cleaned as noted above.
  • Textured or porous surfaces: Will hold but this is the weakest case. Expect reduced contact area and consider the included screw hardware instead of adhesive.

Step 4, Apply pressure, then wait. Apply adhesive to the back side of the mounting pad completly covering the back side of the pad. Press the mount firmly in place allowing the adhesive to push out the sides of the mount pad. Hold in place for a few minutes allowing any trapped air to be push out, then leave it alone for 24 hours. Full cure time matters, so give the adhesive the time to cure inside/out. Do not install clip strips, load baits, slam the lid, or run the boat during the cure window.

Watch OutGive the adhesive its full cure time before mounting the clip strip and loading baits. ( No less than 24 hours)
Pro TipTemperature matters. Adhesive cures best at moderate temperatures; applying a pad in a cold garage or in direct summer sun on a hot lid can weaken the bond before it sets. Bring the boat and the hardware to a comfortable temperature first.

The steps below cover what to check and how long to wait during installation, so the mount bonds properly.

Step

What to do

Time or frequency

Pick the right spot

Choose a flat, smooth area where the mount sits flush

Before mounting

Clean, then clean again

Wipe with isopropyl alcohol using a lint-free cloth

Wipe twice

Match the pad to the surface

Check material compatibility, such as fiberglass or textured plastic

Before applying

Apply pressure, then wait

Press firmly from the center outward, then leave it alone

Full cure time per adhesive instructions

Shop Now →

Picture an open compartment lined with hangers holding crankbaits in view, with soft plastics clipped neatly beside them. Everything is visible, and you can retrieve the bait you need in seconds.

Holding Up in rough water

The Easy View Tackle System is a special designed clip strip to hold up in rough water situations

I M G 0489
I M G 0489

Vibration and shock. Rough water and chop send repeated shock loads through the hull and into every mount. The clip strips are heavy duty spring steel powder coated and can handle more rough water than your boat can.

Best Tackle Clips for Boat Storage

Easy View Tackle clip strips keep baits visible and reachable. See why tournament anglers choose tackle organization strips over other storage approaches. Tackle boxes and trays are the older approach this system replaces.

Leave a Reply

Your email address will not be published. Required fields are marked *